Bug Reports for CFDEM®coupling, LIGGGHTS®, and ParScale

(Possible) bugs / suspicious behavior should be reported as a new thread here, not in the user forum. This should give both you and the developers a clear idea about the status of your bug report (submitted/assigned/fixed)

bug?--using CFDEMsolverIB for cyclic boundary condition

Submitted by fanfengxian on

Hi, Alice,

I am using solverIB to simulate periodic laminar particle-fluid flows in a cylindrical pipe.

In CFD side, I set all the parameters in "0" folder to be cyclic for the inlet and outlet, and set a source in fvOptions to drive the flow. The flow velocity (parabolic) and pressure (uniform) profiles are fine.

In DEM side, the boundary is set to be p f f.
Unfortunately, when I plot the particle velocity(vx, vy, vz) changing with time, I find there is a velocity jump when the particle flows out of the outlet and then flows into the the inlet.

Error in particle inspection and void fraction calculation

Submitted by Mahsa Bagherzadeh on

I have faced a problem in particle inspection and void fraction calculation by CFD side, which I think might be a bug.
When, I insert a particle in the middle of my domain, (100*100*160 mm cube) only a quarter of the particle has been identified by the CFD. On the other hand when I move the center of the particle from p1=(50,50,120) to a bit to the corner to p2=(30,30,120), the whole particle becomes visible.

Unclear feedback in CFDEM from implicitCouple

Submitted by ndeen on

When one changes KslLimit or minAlphaP, the following lines are printed:

implicit momentum exchange field is limited to : 10000
implicit momentum exchange field calculate if alphaP larger than : 1

The first line is OK and shows the value of KslLimit that was supplied.
But the second line shows the value of (1-minAlphaP), whereas it should show the value of minAlphaP.
This can be fixed by changing line 105 in src/lagrangian/cfdemParticle/subModels/momCoupleModel/implicitCouple/implicitCouple.C:

LIGGGHTS 3 - move/mesh for mesh/surface geometry

Submitted by Tijmus on

Apparently move/mesh crashes the run for the non-planar stl-file (an annular cylinder) in my problem, while this setup ran fine in LIGGGHTS 2.3.6. It consists of an annular cylinder, which is: 1. filled with particles 2. compacted by a piston, to achieve a high packing 3. moved in a cylindrical orbiting motion (composed by superposition of an eccentric rotation and a back-rotation around its local origin).

The relevant fixes are "move2" and "move4". Files are attached.

Thanks in advance.

hybrid/overlay not working in LIGGGHTS_3.0.0

Submitted by ericparteli on

Hi,
Please see the attached script that uses a pair_style hybrid/overlay combining hertz/stiffness with lj/cut.
The simulation crashes as soon as the first particle touches one of the walls (at timestep ~9400). If I remove the walls, everything runs fine.
Am I doing something wrong in the script or is there a bug in LIGGGHTS that is preventing one to use (granular) walls when applying the pair style hybrid/overlay?
NOTE: This problem was NOT occurring in LIGGGHTS_2.3.8!
Thanks in advance!
Best
Eric

Error in 'probability_distribution.h'?

Submitted by apeskhov on

Hi all,

I wanted to add a possibility for the fix template/sphere to work in 2 dimensions. So I needed to add respectively the square expectation values in 'probability_distribution.h'.

I think there is an error for the expectancy value of the uniform distribution that you have entered.
For me it will just be: E[x]= (max^2-min^2)/(2*(max-min)) = (max+min)/2
But in the file you have entered: E[x]=[(max+min)/2]^3

Anton

Trouble with Multiprocessors and insert/pack

Submitted by cTop89 on

We're getting inconsistent results running a large fix insert/pack in a very tall cylinder on 32 processors. We have it set up to insert 700,000 particles, but the number we actually get when we run varies widely. On the first run, it generated ~200,000 particles and on a second run it generated ~400,000. (We ran those first two with LIGGGHTS 2.3.6, then we updated to 2.3.8 and ran one more that acted the same and generated ~350,000 particles.)

Building liggghts 2.3.8 with visual studio

Submitted by apeskhov on

Hi,

I have problem to build the latest version of liggghts(2.3.8) with visual studio. I obtain the following errors:

Error 1 error LNK2001: unresolved external symbol ""public: int __thiscall LAMMPS_NS::AtomVecSphere::pack_border_vel_wedge(int,int *,double *,int,int *)" (?pack_border_vel_wedge@AtomVecSphere@LAMMPS_NS@@QAEHHPAHPANH0@Z)" C:\Users\Anton\Downloads\liggghts\LIGGGHTS-PUBLIC\src\WINDOWS\atom_vec_sphere.obj LIGGGHTS-PUBLIC

Restarting

Submitted by RocheDEM on

I have run into a problem when restarting this simulation. It is the 3rd restart. I get the following error:

ERROR: Incompatible mesh restart file - mesh has different properties in restarted simulation (multi_node_mesh_parallel_buffer_I.h:198)

But I can't see that there is any difference in the mesh...

I have attached the pre-restart files and the post-restart files.

Kirk