CFDEM®workbench

For questions and feed-back related to CFDEM®workbench STARTER, please post here!

force fluctuations

Submitted by Ben Lee on

Dear all,

I conducted a multi-phase flow simulation similar to a dam-break , with a slit dam in the center of the tank. When running OpenFoam or LIGGGHTS separately, the results seem normal, but the forces monitored in OpenFoam fluctuate significantly after coupling (the upstream face of the dam). I have considered factors such as boundary conditions, mesh size, and particle gradation, but the problem remains unresolved. Turning off the void fraction model reduces the fluctuations, but the issue still exist.

Problem with fix move/mesh command

Submitted by Zakia on

Hi,
I am trying to run a FT4 simulation where an impeller is rotating and moving downwards. The issue is I am getting similar force with different speeds. Has anybody faced anything like that? Can someone help me with that please?
The commands that I am using is:
#rotate the impeller
fix move1 all move/mesh mesh mesh_impeller rotate origin 0.0 0.0 0.0 axis 0.0 1.0 0.0 period ${i_period}
fix move 2 all move/mesh mesh mesh_impeller linear 0.0 0.0 -0.00875

any help would be greatly appreciated.

Thank you

About memory comsuption

Submitted by KesleyAS on

Greetings,

I'm developing a flow simulation in a bed with gravel. The simulation contains 800k particles in a 2.0x0.8x0.2 bed, but as the simulation progresses the RAM memory consumption increases a lot, to the point of causing an error (signal 9). I intend to simulate a flowtime of approximately 500s. Could someone give me tips to reduce this memory consumption? I tried to implement the fix freeze , but the particles didn't freeze as I thought, I tried to implement the neigh_modify exclude after the particles settled, but it wasn't enough.

The script was pasted below:

Error 'youngModulus <==1e9 required for SI units' (Aspherix GUI)

Submitted by zhbkro on

Hi all,

I'm trying to understand how vibration affects segregation of particles composed of glass beads. When I apply more than 1e9 Pa for Young's modulus, the Aspherix shows an error 'youngModulus <==1e9 required for SI units (use command 'hard particles yes' to override it). So, I could not find this command in Aspherix GUI program in 'material properties' section. Could you please give some hint how to solve it?

Ps. Or should I use other units? i haven't tried to use other units yet.

Cannot order the CFDEM Workbench Starter

Submitted by felixsihombing on

I want to start learning the CFDEM Workbench for geological application. The CFDEM Workbench Starter will be my preference to learn how things work in this software. However, i cannot access the order page properly when visiting the link (https://www.dcs-computing.com/order-product?product=13868). The displayed page only state "You are not authorized to access this page".

Any help is much appreciated.

how to rotate the same fix mesh with different origin

Submitted by mar_co on

Hi all,
I am new with liggghts
I am try to rotate the same fix mesh with different origin and different running step
When I run a simulation which includes a mesh rotation about 2 different axis I get a different rotations in the first running, it is running fine.
But at the second running, i get the error as follows : " ERROR: Illegal deletion of a fix move/mesh. There is another fix move/mesh command active on the same mesh. Superposed fix move/mesh commands must be unfixed in reverse order of creation (fix_move_mesh.cpp:137) "

fix insert/pack command in LIGGGHTS-WORKBENCH-STARTER 4.0.0

Submitted by Andrey on

Hello everyone,

I get an error when I run the example problem "packing" (from Tutorials_public folder):

# last command:
fix ins nve_group insert/pack seed 32452867 distributiontemplate pdd1 maxattempt 200 insert_every once overlapcheck yes all_in yes vel constant 0. 0. 0. region reg volumefraction_region 0.25

ERROR: Invalid fix style: "insert/pack"