Hi Everybody,
I am trying to set up CFDEMproject on ubuntu 14.04 LTS, and I am following the same exact steps on githubAccess_public.pdf.
I installed OpenFOAM-2.3.x successfully, and everything went fine up to
cfdemSysTest
and I get some information confirming that the paths are set correctly.
Then I started compiling LIGGGHTS(R) by typing:
cfdemCompLIG
The compilation run for a while and in the end gave me the following :
“.
.
.
a - write_dump.o
a - write_restart.o
make[1]: Leaving directory `/home/almsahli6/LIGGGHTS/LIGGGHTS-PUBLIC/src/Obj_fedora_fpic'
Compiling sub-libraries of LIGGGHTS now...
Please provide the libraries to be compiled in the //home/almsahli6/CFDEM/CFDEMcoupling-PUBLIC-/src/lagrangian/cfdemParticle/etc/library-liggghts-list.txt file.
Libraries must be in the /home/almsahli6/LIGGGHTS/LIGGGHTS-PUBLIC/src/../lib directory.
”
I am not sure what Libraries I need to provide or change.
Because also compiling CFDEM(R)coupling after that broke very quick.
Could someone help me to solve this matter please , or if you recommended better installation guide.
Regards,
Hasan
afaik only OpenFoam 2.2.x is known to work
afaik you need to use OpenFoam 2.2.x, and make sure you checked out the commit 61b850bc107bdd60bbf1bf9a6417b9faf701d128 (last one compatibel with CFDEMCouplingToolbox)
cd $HOME
mkdir OpenFOAM
cd OpenFOAM
git clone https://github.com/OpenFOAM/OpenFOAM-2.2.x.git
git checkout 61b850bc107bdd60bbf1bf9a6417b9faf701d128
cd $HOME/OpenFoam/OpenFoam-2.2.x/
./Allmake
Make sure to adapt the .bashrc to the right paths for OF2.2.X and source it new !
The output of cfdemCompLIG does not seems to be an error, only a message what happend there / next - not critical in my opinion.
Best,
Christian
In reply to afaik only OpenFoam 2.2.x is known to work by richti83
Hi Christian, Thanks for your
Hi Christian, Thanks for your reply. I installed OF2.2.x as you suggested I also tried OF2.1.x just in case but after Liggghts compilation (cfdemCompLIG) I still got the same results in each case.
".
.
a - write_data.o
a - write_dump.o
a - write_restart.o
make[1]: Leaving directory `/home/almsahli12/LIGGGHTS/LIGGGHTS-PUBLIC/src/Obj_fedora_fpic'
Compiling sub-libraries of LIGGGHTS now...
Please provide the libraries to be compiled in the //home/almsahli12/CFDEM/CFDEMcoupling-PUBLIC-/src/lagrangian/cfdemParticle/etc/library-liggghts-list.txt file.
Libraries must be in the /home/almsahli12/LIGGGHTS/LIGGGHTS-PUBLIC/src/../lib directory."
Do you think that I might be still missing something else?
Thanks,
Hasan
I think this output is OK,
I think this output is OK, can't see any error.
You can check if there is a lmp_fedora_fpic and a liblmp_fedora_fpic.a in your LIGGGHTS/LIGGGHTS-PUBLIC/src/ directory.
Next step is to type cfdemCompCFDEM and see what happens. After that you can test the Tutorials in the CFDEM folder.
Best,
Christian
In reply to I think this output is OK, by richti83
Thanks Christian, the CFDEM(R
Thanks Christian, the CFDEM(R) compiled quite fine this time I think. But I have got an error when running tutorial cases ( using cfdemTestTUT and Allrun.sh)
.. ..................................
(Under the console screen of "cfdemSolverPiso settlingTest CFD" gives:)
.
.
** (evince:29668): WARNING **: Error setting file metadata: No such file or directory
** (evince:29668): WARNING **: Error setting file metadata: No such file or directory
.......................................
(and under the "Document Viewer" gives :)
Unable to open document “file:///home/almsahli8/CFDEM/CFDEMcoupling-PUBLIC-2.2.x/tutorials/cfdemSolverPiso/settlingTestMPI/CFD/octave/cfdemSolverPiso_settlingTestMPI.eps”.
Error opening file: No such file or directory
.......................................
Runing the other tutorial cases give similar results.
Do you have any suggestion what could have caused this problem.
Many Thanks,
Hasan
I predict you did not install
I predict you did not install octave to convert the result files into a chart. Can you post the full log of the cfdemrun terminal ?
When there is one line which tells you the system did not find octave and you are on a ubuntu/debian system just type
sudo apt get install ocatve
A good way to check the results is to use ParaView:
install the latest binary from paraview.org (4.0.1).
create an alias in in your bashrc to the binary of paraview for example:
alias paraview='$HOME/Downloads/ParaView-4.1.0-Linux-64bit/bin/paraview --use-old-panels'
Than in the terminal where you typed Allrun type:
source $HOME/.bashrc
touch mycase.foam
paraview
Open the mycase.foam file and watch the beautiful colors of your simulation.
How did you solve Library Requirement
HI Hassan,
I got the same problems when doing cfdemCompLIG, it states that " Please provide the libraries to be compiled in the... and Libraries must be in..."
I have checked mp_fedora_fpic and a liblmp_fedora_fpic.a and found them avaiable in the directory.
Please advise my problems,
Thanks,
Regards,